基本信息：

Product Introduction: 

JS聚合物水泥基防水涂料是由合成高分子聚合物乳液（如聚丙烯酸酯、聚醋酸乙烯酯、丁苯橡膠乳液）及各種添加劑優化組合而成的液料復合而成的單組分防水涂料，是一種既具有合成高分子聚合物材料彈性高、又有無機材料耐久性好的防水材料。

JS Polymer waterproof slurry is made from Synthesis of polymer emulsion(such as polyacrylate, polyvinyl acetate, styrene butadiene rubber emulsion)and various additives. Therefore, it is a waterproof material with high elasticity and good durability.

適用范圍：

Scope of application

可在潮濕或干燥的磚石、砂漿、混凝土、金屬、木材、硬塑料、玻璃、石膏板、泡沫板、橡膠、等基面上施工。對于新舊建筑物及構造物（例如：房屋、地下工程、隧道、橋梁、水池等）均可使用，同時也可做粘貼劑使用（歡迎免費注冊，登陸中國涂料在線（涂料在線）行業門戶網址www.zx446.com，免費發布供求，免費發布產品，免費發布企業動態）。特別適合地下室、地下隧道、衛浴間、水池等，特別潮濕及長期在水中浸泡的條件下的施工。

It can be applied on the surface of wet or dry masonry, mortar, concrete, metal, wood, hard plastic, glass, gypsum board, foam board, rubber, and so on. Its applicable to houses, underground works, tunnels, bridges, pools, etc too. They can also be used as stickers, especially suitable for basement, underground tunnel, bathroom room, pool, etc., where the place is wet and immersed in water for a long time.

產品特性：

Features

1. 環保型產品、Ⅰ型耐紫外線，耐老化，特別適用于屋面防水工程；

Its a kind of environmental products. Type “I” has feature of UV resistance, aging resistance, especially suitable for roof waterproofing engineering.

2. 可作飲水工程，特別適用于長期進水的防水工程；

It can be used as drinking water engineering project, especially suitable for long-term influent waterproofing project.

3. 可在潮濕面上施工、工期短、操作方便；

It can be constructed on wet surface. It has feature of short construction period and convenient operation.

4. 涂層高彈、粘接力強、耐腐蝕；

Has high elasticity, strong adhesion and corrosion resistance.

5. 可錕、可刷、批刮、堵漏、修補。防水層具有整體無縫的特性；

Can be brushed, scraped, blocked and repaired. The waterproof layer is seamless as a whole.

6. 具有抗震性，可適應基層微小變形，能起到遮蔽裂紋和抑制表面產生裂紋的作用。

It ‘s seismic resistance, adapt to the small deformation of the base, and can cover the crack and inhibit the crack on the surface.

基面處理：

Base surface dispostion

1. 基面必須穩固、清潔、平整、無灰塵、無油污。假如有明顯的空隙、砂眼需要用水泥砂漿堵塞、抹平，尖銳的邊緣應除去。

The base surface must be stable, clean, flat, dust-free and oil-free. If there are obvious voids and sandholes, must block and smooth them using cement mortar. Sharp edges should be removed too.

2. 滲漏處須先進性堵漏處理，陰陽角應做成圓弧形。

The leakage place must be blocked in advance. The internal angle and external angle should be made into a circular arc.

施工說明：

Construction Guidance

首先，將添加劑倒進桶（或其他容器）內，用慢速電鉆（約4000轉/分）攪拌，同時慢慢加入配套的粉料，攪拌4-5分鐘直至均勻，然后靜至5分鐘才可以使用。

如果基層過于干燥，先用水將基面稍微濕潤（無明水為準）。對可能會產生裂縫的地方，要鋪設胎體增強材料。配置好的涂料應在4小時內用完。

涂刷至少兩遍，第二遍必須等到上次干固不粘手方可進行。兩次涂刷需要交叉垂直，這樣才能達到最好的覆蓋效果。

First of all, pour the additive into the bucket (or other container), stir with a slow electric drill (about 4000 rpm / min), and slowly add the matching powder, stir for 4- 5 minutes until it become even, and then place it statically for 5 minutes before you use it.

If the base layer is too dry, moisturize the base a little but not make it to wet to see water. Reinforce it to where cracks may occur. The configured paint should be used up within 4 hours.

Brushing should be twice at least, the second time must wait until it become dry and not stick to the hand. Two brushes should be cross-vertically in order to achieve the best coverage effect

執行標準：

Execution Standards:

JSⅡ GB23445-2009《聚合物水泥防水涂料》

JSⅡ GB23445-2009《Polymer cement waterproof coating 》

保質日期和存儲

Validity Period & Storage conditions

原裝密封產品放于陰涼干燥處，有效期為一年。

Original sealed products should be placed in dry and cool places. The validity period is 12 months.